Revision as of 08:11, 17 March 2017

Download Kernel

You can clone the rockchip kernel repository from github which is kernel 4.4 based:

git clone https://github.com/rockchip-linux/kernel.git

Supported SoCs and Devices

Rockchip kernel 4.4 supports:

RK3036, RK3066, RK312X, RK3188, RK322X,RK3288, RK3328, RK3368, RK3399

Configure and Build

You will need to use rockchip_linux_defconfig for Linux OS

configure for armv7:

make rockchip_linux_defcofig

configure for aarch64:

make ARCH=arm64 rockchip_linux_defconfig

After configure, you need to decide which board to use, get the dts file name, and replace its postfix to img in make command,

For armv7:

make rk3288-firefly.img -j8

For aarch64:

make ARCH=arm64 rk3399-evb.img -j8

Then you can get Image/zImage and dtb file.

Install Boot/kernel

We use distro boot in U-Boot, so we need to make a boot partition for U-Boot with kernel image and dtb inside.

mkdir boot
cp arch/arm64/boot/dts/rockchip/rockchip/rk3399-evb.dtb boot/rk3399.dtb
cp arch/arm64/boot/Image boot/

Add extlinux/extlinux.conf for distro boot.

mkdir boot/extlinux
vi boot/extlinux/extlinux.conf

lable rockchip-kernel-4.4
    kernel /Image
    fdt /rk3399.dtb
    append earlycon=uart8250,mmio,0xff1a0000 root=dev/mmcblk1p7 rootwait rootfstype=ext4 init=/sbin/init

You need to change the base address of debug UART, root partition for your board.

Pls reference to rockchip Linux parttion definition for rootfs partition and where boot to flash.

After all these file prepare complete, we write the file to the boot partition

Generate ext2fs boot partition

by genext2fs:

genext2fs -b 32768 -B $((32*1024*1024/32768)) -d boot/ -i 8192 -U boot_rk3399.img

According to Rockchip partition definition, you need to flash this image to boot partiton which offset is 0x8000.

dd this image to sd card, see sd_boot,

or write to emmc with rkdeveloptool, see emmc_boot.

generate fatfs boot partition

Via U-Boot in target

After flash and boot the U-Boot, write the gpt table from default partition table

gpt write mmc 1 $partitions
gpt verify mmc 1 $partitions

connect target to PC and start the ums in command line:

ums 0 mmc 1:6

We should able to see a device connect to PC, formate and copy data into the partition(dev/sdb6 for example).

sudo mkfs.fat /dev/sdb6
cp -r boot/* /media/machine/9F35-9565/

Generae boot.img in fatfs

Below commands can generate a fatfs boot.img

dd if=/dev/zero of=boot.img bs=1M count=32
sudo mkfs.fat boot.img
mkdir tmp
sudo mount boot.img tmp/
cp -r boot/* tmp/
umount tmp

Done!

Flash this boot.img to boot partition, which is offset 0x8000 in Rockchip partition definition.

Boot from U-Boot

If everything is OK, you should able to see the U-Boot log like this:

switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:6...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
205 bytes read in 82 ms (2 KiB/s)
1:      upstream-4.10
Retrieving file: /Image
13484040 bytes read in 1833 ms (7 MiB/s)
append: earlycon=uart8250,mmio32,0xff1a0000 console=ttyS2,1500000n8 rw root=/dev/mmcblk0p7 rootwait rootfstype=ext4 init=/sbin/init
Retrieving file: /rk3399.dtb
61714 bytes read in 54 ms (1.1 MiB/s)
## Flattened Device Tree blob at 01f00000
   Booting using the fdt blob at 0x1f00000
   Loading Device Tree to 000000007df14000, end 000000007df26111 ... OK

Starting kernel ...