Boot option

From Rockchip open source Document
Revision as of 06:53, 23 March 2017 by Kever (talk | contribs)
Jump to: navigation, search

 

 

Boot introduce

 

First, let's make the concept clear, there are many boot stages when we boot up a Linux OS;

Then we need to know about how the image should packaged, where the image locate;

At lase, we will explain how to write to different media and boot from there.

Boot stage

Here is a table show the detail what we may use in Rockchip platform, for 2 boot stage:

- optionally can use U-Boot SPL;

-  or use Rockchp idbLoader which is combinded by Rockchip ddr init bin and miniloader bin;

+--------+----------------+----------+-----------+
| Boot   | Terminology #1 | Actual   | Rockchip  |
| stage  |                | program  |  Loader   |
| number |                | name     |   Name    |
+--------+----------------+----------+-----------+
| 1      |  Primary       | ROM code | BootRom   |
|        |  Program       |          |           |
|        |  Loader        |          |           |
|        |                |          |           |
| 2      |  Secondary     | U-Boot   | idbLoader | 0x40
|        |  Program       | SPL      |           |
|        |  Loader (SPL)  |          |           |
|        |                |          |           |
| 3      |  -             | U-Boot   |  U-Boot   | 0x4000
|        |                |          |           |
|        |                |          |           |
| 4      |  -             | kernel   |  kernel   | 0x8000
|        |                |          |           |
| 5      |  -             | rootfs   |  rootfs   | 0x40000
+--------+----------------+----------+-----------+

Then when we talking about boot from eMMC/SD/U-Disk/net, they are in different concept:

  • Stage 1 is always in boot rom, it loads stage 2 and may load stage 3(when SPL_BACK_TO_BROM option enabled).
  • Boot from SPI flash means firmware for stage 2 and 3(SPL and U-Boot only) in SPI flash and stage 4/5 in other place;
  • Boot from eMMC means all the firmware(including stage 2, 3, 4, 5) in eMMC;
  • Boot from SD card means all the firmware(including stage 2, 3, 4, 5) in SD card;
  • Boot from U-Disk means firmware for stage 4 and 5(not including SPL and U-Boot) in Disk, optionally only including stage 5;
  • Boot from net/tftp means firmeware for stage 4 and 5(not including SPL and U-Boot) on the network;

Package option

After we know about the boot stages,

Here are the file list before package for stage 2~4:

  • From source code:
    • From U-Boot: u-boot-spl.bin, u-boot.bin(may use u-boot-nodtb.bin and u-boot.dtb instead),
    • From kernel: kernel Image/zImage file, kernel dtb,
    • From ATF: bl31.bin;
  • From Rockchip binary:
    • ddr, usbplug, miniloader, bl31, (all with chip 'rkxx_'  prefix and with version '_x.xx.bin' postfix);

Here are the types to package image from those files:

idbspl.img

U-Boot SPL, with SPL_BACK_TO_BROM option disabled.

mkimage -n rkxxxx -T rksd -d spl/u-boot-spl.bin idbspl.img

Flash the idbspl.img to offset 0x40 which only including stage 2, and need flash stage 3  image to 0x200(which is defineded by CONFIG_SYS_MMCSD_RAW_MODE_U_BOOT_SECTOR), the stage 3 image may be u-boot.bin directly(when there no ATF requirement), or FIT image bl3.itb(for ATF load from SPL, including bl31.bin, u-boot-nodtb.bin and u-boot.dtb).

idbloader.img

U-Boot SPL, with SPL_BACK_TO_BROM option enabled:

tools/mkimage -n rkxxxx -T rksd -d spl/u-boot-spl.bin idbloader.img
cat u-boot.bin >> idbloader.img

Flash the idbloader.img to offset 0x40 which including boot stage 2 and 3.

Package the image from Rockchip binary:

tools/mkimage -n rkxxxx -T rksd -d rkxx_ddr_vx.xx.bin idbloader.img
cat rkxx_miniloader_vx.xx.bin >> idbloader.img

Flash the idbloader.img to offset 0x40 which including stage 2, and you will need a uboot.img for boot stage 3.

bl3.itb

When using SPL to load the ATF, package the bl31.bin, u-boot-nodtb.bin and uboot.dtb into one FIT image.

tools/mkimage -f fit4spl.its -E bl3.itb

Flash the bl3.itb to offset 0x200, while need idbspl.img flasht to offset 0x40.

uboot.img

When using idbLoader from Rockchip miniloader, need package u-boot.bin into miniloader loadable format by Rockchip tool loaderimage.

tools/loaderimage --pack --uboot u-boot.bin uboot.img

Flash the uboot.img to offset 0x4000 which is stage 3;

trust.img

When using idbLoader from Rockchip miniloader, need package bl31.bin into miniloader loadable format by Rockchip tool trustmerge.

tools/trustmerge tools/rk_tools/RKTRUST_RKXXXXTRUST.ini

Flash the trust.img to offset 0x6000 which is for using Rockchip miniloader


rkxx_loader_vx.xx.xxx.bin

This is provide by Rockchip in binary mode, which is used for firmware upgrade to eMMC with rkdeveloptool, can not be wirte to media device directly.

This is a package from ddr.bin, usbplug.bin, miniloader.bin, Rockchip tool DB command will make usbplug.bin running in target which perform as a Rockusb device.

boot.img

This image is package the kernel Image and dtb file into a know filesystem(FAT or EXT2) image for distro boot.

See Install kernel for detail about generate boot.img from kernel zImage/Image, dtb.

Flash the boot.img to offset 0x8000 which is stage 4.

rootfs.img

Flash the rootfs.img to offset 0x40000 which is stage 5.

Flash and boot from Media device

Here we introduce how to write image to different Medeia device.

Get image Ready:

  • For armv7 with SPL with SPL_BACK_TO_BROM option enabled:
    • idbLoader.img
    • boot.img or boot folder with zImage, dtb and exitlinulx inside
    • rootfs.img
  • For armv7 with SPL with SPL_BACK_TO_BROM option disabled:
    • idbspl.img
    • u-boot.bin
    • boot.img or boot folder with zImage, dtb and exitlinulx inside
    • rootfs.img
  • For armv7 with miniloader
    • idbLoader.img
    • uboot.img
    • boot.img or boot folder with zImage, dtb and exitlinulx inside
    • rootfs.img
  • For armv8 with SPL:
    • idbspl.img
    • bl3.itb
    • boot.img or boot folder with zImage, dtb and exitlinulx inside
    • rootfs.img
  • For armv8 with miniloader
    • idbLoader.img
    • uboot.img
    • trust.img
    • boot.img or boot folder with zImage, dtb and exitlinulx inside
    • rootfs.img

 

Boot from eMMC

The eMMC is on the hardware board, so we need:

Example commands for flash image to target.

  • For armv7 with SPL with SPL_BACK_TO_BROM option enabled(rk3036, rk3188, rk3288):
rkdeveloptool db rkxx_loader_vx.xx.bin
rkdeveloptool wl 0x40 idbloader.img
rkdeveloptool wl 0x8000 boot.img
rkdeveloptool wl 0x40000 rootfs.img
rkdeveloptool rd
  • For armv7 with SPL with SPL_BACK_TO_BROM option disabled(rk3288):
rkdeveloptool db rkxx_loader_vx.xx.bin
rkdeveloptool wl 0x40 idbspl.img
rkdeveloptool wl 0x200 u-boot.bin
rkdeveloptool wl 0x8000 boot.img
rkdeveloptool wl 0x40000 rootfs.img
rkdeveloptool rd
  • For armv7 with miniloader(rk3036, rk3188, rk3288)
rkdeveloptool db rkxx_loader_vx.xx.bin
rkdeveloptool wl 0x40 idbloader.img
rkdeveloptool wl 0x4000 uboot.img
rkdeveloptool wl 0x8000 boot.img
rkdeveloptool wl 0x40000 rootfs.img
rkdeveloptool rd
  • For armv8 with SPL(rk3399):
rkdeveloptool db rkxx_loader_vx.xx.bin
rkdeveloptool wl 0x40 idbspl.img
rkdeveloptool wl 0x200 bl3.itb
rkdeveloptool wl 0x8000 boot.img
rkdeveloptool wl 0x40000 rootfs.img
rkdeveloptool rd
  • For armv8 with miniloader(rk3399, rk3328)
rkdeveloptool db rkxx_loader_vx.xx.bin
rkdeveloptool wl 0x40 idbloader.img
rkdeveloptool wl 0x4000 uboot.img
rkdeveloptool wl 0x6000 trust.img
rkdeveloptool wl 0x8000 boot.img
rkdeveloptool wl 0x40000 rootfs.img
rkdeveloptool r


Boot from SD/TF Card

We can write SD/TF card with Linux PC dd command very easily.

Insert SD card to PC and we assume the /dev/sdb is the SD card device.

  • For armv7 with SPL with SPL_BACK_TO_BROM option enabled(rk3036, rk3188, rk3288):
dd if=idbloader.img of=sdb seek=0x40
dd if=boot.img of=sdb seek=0x8000
dd if=rootfs.img of=sdb seek=0x40000
  • For armv7 with SPL with SPL_BACK_TO_BROM option disabled(rk3288):
dd if=idbspl.img of=sdb seek=0x40
dd if=u-boot.bin of=sdb seek=0x200
dd if=boot.img of=sdb seek=0x8000
dd if=rootfs.img of=sdb seek=0x40000
  • For armv7 with miniloader(rk3036, rk3188, rk3288)
dd if=idbloader.img of=sdb seek=0x40
dd if=uboot.img of=sdb seek=0x4000
dd if=boot.img of=sdb seek=0x8000
dd if=rootfs.img of=sdb seek=0x40000
  • For armv8 with SPL(rk3399):
dd if=idbspl.img of=sdb seek=0x40
dd if=bl3.itb of=sdb seek=0x200
dd if=boot.img of=sdb seek=0x8000
dd if=rootfs.img of=sdb seek=0x40000
  • For armv8 with miniloader(rk3399, rk3328)
dd if=idbloader.img of=sdb seek=0x40
dd if=uboot.img of=sdb seek=0x4000
dd if=trust.img of=sdb seek=0x6000
dd if=boot.img of=sdb seek=0x8000
dd if=rootfs.img of=sdb seek=0x40000

In order to make sure everything has write to SD card before unpluged, recommand to run below command:

sync

Note, when using boot from SD card, need to update the kernel cmdline(which is in extlinux.conf) for the correct root value.

append  earlyprintk console=ttyS2,115200n8 rw root=/dev/mmcblk1p7 rootwait rootfstype=ext4 init=/sbin/init

Write GPT partition table to SD card in U-Boot, and then U-Boot can find the boot partition and run into kernel.

gpt write mmc 0 $partitions


Boot from U-Disk

Same as boot-from-sdcard, but please note that U-Disk only support stage 4 and 5, see Boot Stage for detail.

If U-Disk used for stage 4 and 5, format the U-Disk in gpt format and at least 2 partitions, write boot.img and rootfs.img in those partitions;

if U-Dist is only used for stage 5, we can dd the rootfs.img to U-Disk device directly.

Note, need to update the kernel cmdline(which is in extlinux.conf) for the correct root value.

    append  earlyprintk console=ttyS2,115200n8 rw root=/dev/sda1 rootwait rootfstype=ext4 init=/sbin/init

Boot from Network